torque sequence on 1998 ford 4 2 intake manifold

You search Content Auto service manual ebook pdf torque sequence on 1998 ford 4 2 intake manifold, If search results do not exist, please search by others keyword.

2002 Ford Taurus V6-183 3.0L VIN U SFI Upper Intake Manifold Service and Repair

7

Filed Under (Ford) by admin on 29-11-2012

2002 Ford Taurus V6-183 3.0L VIN U SFI Upper Intake Manifold Service and Repair download Removal 1. Disconnect the battery ground cable. 2. Remove the air cleaner assembly and the air cleaner outlet tube. 3. Remove the pin-type retainers and the snow shield. 4. Disconnect the accelerator cable, speed control actuator cable and the throttle return spring from the throttle body. 5. Remove the bolts, then position the accelerator cable bracket asi…

Download Full 2002 Ford Taurus V6-183 3.0L VIN U SFI Upper Intake Manifold Service and Repair.pdf

1999 Ford Truck F 250 2WD Super Duty Intake Manifold Service and Repair

4

Filed Under (Ford) by admin on 10-10-2013

1999 Ford Truck F 250 2WD Super Duty Intake Manifold  Service and Repair download 1. Position the lower intake manifold gasket and the upper intake manifold on the intake manifold and loosely install the ten bolts. 2. NOTE: Tighten the bolts in two stages. Tighten the bolts in the sequence shown. Stage 1: Tighten to 2 Nm (18 inch lbs.) Stage 2: Tighten to 8-12 Nm (71-106 inch lbs.) 3. If required, install the fuel injector supply manifold. Posi…

Download Full 1999 Ford Truck F 250 2WD Super Duty Intake Manifold Service and Repair.pdf

2000 Ford Windstar Intake Manifold

6

Filed Under (Ford) by admin on 13-07-2014

download Removing 1. Partially drain the cooling system. For extra info, confer with Section 303-03. 2. Remove the higher intake manifold (9424). For additional info, check with Intake Manifold-Upper on this section. 3. Remove the gas provide manifold (9F792). For extra information, discuss with Section 303-04B. 4. Disconnect the EGR vacuum tube (9E498).5. Disconnect the EGR-to-exhaust manifold tube (9D477). Loosen the nut. 6. Disconnect the up…

Download Full 2000 Ford Windstar Intake Manifold.pdf

2003 Acura MDX Intake Manifold Repair

5

Filed Under (Acura) by admin on 14-04-2013

two or three steps, then take away the higher cover. Take away the intake manifold mounting bolts and nuts sequentially in two or three steps, then take away the intake manifold and spacer. Set up Set up the gasket and spacer on the injector base. Set up the intake manifold. Tighten the bolts and nuts sequentially in two or three steps. Always use a brand new intake manifold gasket. 3. Set up the upper cover. Tighten the bolts and nuts sequential…

Download Full 2003 Acura MDX Intake Manifold Repair.pdf

2001 Ford Windstar COWL TOP VENT PANEL

6

Filed Under (Ford) by admin on 01-11-2013

l rail and injectors as an assembly. 5. Note location of lower intake manifold bolts and studs. Remove lower intake manifold bolts and studs. Remove lower intake manifold. If necessary, break intake manifold sealing by prying on front of manifold with flat screwdriver. Remove and discard gaskets. Incoming search terms: 2001 ford ranger lower intake manifold torque,2001 f 250 cowl leak,how to remove intake manifold on 3 0L v6 ford ranger,torque &a…

Download Full 2001 Ford Windstar COWL TOP VENT PANEL.pdf

FORD 4.6 LITER INTAKE MANIFOLD INSTALLATION INSTRUCTIONS

2

Filed Under (Ford) by admin on 22-11-2013

per the service procedure outlined in the shop manual. 2. Clean mounting surface. 3. Reinstall intake manifold per shop manual. 4. Tighten intake bolts to 25 nm (18 ft/lb). DO NOT OVERTIGHTEN! 5. Use the graphic below for the torque sequence….

Download Full FORD 4.6 LITER INTAKE MANIFOLD INSTALLATION INSTRUCTIONS.pdf

2002 Chevrolet Chevy Suburban Replacement/ Removal Procedure Intake Manifold

1

Filed Under (Chevrolet) by admin on 21-11-2013

fold. 10. Remove the positive crankcase ventilation (pcv) hose with valve. 11. Remove the map sensor (1) from the intake manifold. Incoming search terms: 99 suburban exhaust replacement procedure,How to remove intake manifold on a 2007 Chevy Suburban…

Download Full 2002 Chevrolet Chevy Suburban Replacement/ Removal Procedure Intake Manifold.pdf

2006 Ford Five Hundred SE Upper Intake Manifold Removal Manuals

1

Filed Under (Ford) by admin on 13-02-2014

…. 4. Take away the four transaxle roll restrictor cross brace bolts.5. Take away the bolt and the transaxle roll restrictor cross brace. 6. Disconnect the evaporative emissions (EVAP) canister purge valve tube from the higher intake manifold and detach the retainer. 7. Disconnect the optimistic crankcase air flow (PCV), brake booster and vacuum harness tubes from the higher intake manifold. 8. Detach the fuel tube retainer from the higher intake

Download Full 2006 Ford Five Hundred SE Upper Intake Manifold Removal Manuals.pdf

1998 Ford Ranger Intake Manifold—Lower

2

Filed Under (Ford) by admin on 12-06-2013

sen tensioner.2. Remove belt.9. Remove the upper radiator hose (8260).10. Disconnect the heater hoses from the intake manifold (9424) and the thermostat housing. Position the hoses out of the way.11.WARNING: Fuel supply lines on vehicles equipped with fuel injected engines remain pressurized for long periods of time after engine shut down. Fuel systempressure must be relieved prior to fuel system repair to prevent possible injury.Using the Fuel P…

Download Full 1998 Ford Ranger Intake Manifold—Lower.pdf

2000 Mercury Cougar Lower Intake Manifold Removal Installation Manual

2

Filed Under (Mercury) by admin on 18-09-2014

download Remove the higher consumption manifold. For additional data, check with Upper Intake Manifold on this section. 2. Disconnect the gasoline line spring lock couplings. For additional info, consult with Part 310-00. 3. Disconnect the gasoline stress sensor. 1. Disconnect the fuel strain sensor electrical connector. 2. Disconnect the gas stress vacuum line. 4. Disconnect the fuel injector electrical connectors and position the wiring harne…

Download Full 2000 Mercury Cougar Lower Intake Manifold Removal Installation Manual.pdf